Hook up two subs mono amp

So now that you've decided to purchase two or four subs, its time to show you how to connect them up properly to ensure you achieve the maximum benefits of a multi sub system this article has been recently updated to incorporate two youtube video discussions - 1. Recently i hooked up a friends amp that was a mono block with 2 inputs for speaker wires (2 + and 2-) he had 2 4 ohm dvc subsi followed the 12 volt subwoofer wiring diagram that said to hook the 2 subs up together in parallel to get a 1 ohm load. Having 2 subs doesn`t make them stereo, stereo is a dedication of 2 separate left and right channels whereas the sub channel is a dedicated sub frequency mono channel you can have 2 to give you a bit more oomph as you say and you could expect an increase in output of 3-6 db.

Sign in to youtube sign in play next how to hook up two 4 ohms subwoofers @ 2 ohms on a mono block amp by casperskafs 7:38 play next how to hook up a crossover to your amp by casperskafs 9:00 play next play now new project / civic hatchback bass car by casperskafs. It just like bridgeing the amp get two wires and hook it up to the pos and neg and run it to the subs sparky3489 since the amp isn’t 1 ohm stable, you can’t wire both of those subs wiring them in parallel will result in a 134 ohm load. The sub has 2 8 woofers, and my sony receiver has 2 sub outputs so should i set it up as mono or stereo i have the jbl installed vertically on the wall, so the right would be on top and left on bottom if stereo is used. Instead of messing around with bridging two channels, you simply hook up the single channel of a mono amp to a corresponding subwoofer, and you’re good to go if you’re relatively new to the world of amps and subs, and you’re going the diy route, this bet is definitely your safest.

You can hook up 20 subs to a mono amp but you have to co nfigure the speakers by impedance/ohms if you hook two 2 ohm speakers to a 4 ohm steady amp in parallel you will soon buy a new amp. Can u hook up 2 subs to a mono amp gay dating for hiv positive 5 rear free online dating sites no subscription india speakers just the front with a 4 channel can u hook up 2 subs to a mono amp amp. A mono amplifier is stable to 2 ohms, meaning a mono amp can resist that measurement of electrical current this enables a mono amp to deliver efficient power (watts) to a pair of subwoofers rated at up to 4 ohms each without the need for a second amplifier.

That amp is rated for 2 ohms minimum so wire one voice coil per speaker in parallel that will max out the power of the amp and avoid the loss of quality of a series connection. I have a bp12001 that is 1 ohm mono stable supposedly it has dual speaker hook-ups if i have 2 dual 2 ohm subs wires to 4 ohms each and i hook them both to to a individual connection on the amp (+-+-), am i going to be running the amp at 2 ohms or 8 ohms. Several rockford fosgate mono amplifiers, especially models 2004 and newer, have two sets of speaker terminals these amplifiers are single ended amplifier designs and therefore consist of only one amplifier channel.

How to hook up subwoofers to an amp if you have a passive sub or your amplifier lacks a sub out jack, you can connect the amplifier and subwoofer like you'd connect two speakers use the main (left and right) speaker output terminals on the amplifier and connect to the subwoofer's speaker inputs be sure that the polarities of each. I currently have a sub and 4 speakers hooked up to a amp i want to know if i get another mono amp for my sub only, would it make a huge difference with the sound and also do i need to hook up that one amp directly to my car's battery to give it power or could i kinda bridge it to my old amp i have any help will be greatly appreciated. Well your amp can do 1700 watts at 2 ohms or 1200 watts at 4 ohms you can wire each sub's voice coils in parallel and then wire the subs together in series to get a 2 ohm load to your amplifier you could also wire each sub's voice coils in series and then wire the subs together in series again to get an 8 ohm load.

Brandon inkel: so i could hook up 2 8ohm subs to a 4ohm amp the amp is mono 250 watt max and the subs are 8 ohm 100w rms 250w max the amp is mono 250 watt max and the subs are 8 ohm 100w rms 250w max. Jawaban terbaik: first off, if its a mono amp, then it is not bridgeable and based off of the first two ratings you list, i'm going to guess you have the alpine mrp-m450, but i don't know where you came up with the bridged power ([email protected]) from. To avoid your high-powered amplifier from overheating, as well as damage to both your amp and subs, the ohms you drive your amp with must not be lower than what it is designed to handle some low-impedance wiring diagrams are included. The subwoofer is hooked up to the receiver with a single interconnect cable stereo receivers, pre-amps, and integrated amplifiers rarely have subwoofer output jacks or offer bass-management options.

  • If you've got a mono amplifier, you've got a great opportunity to really bring on the bass mono amplifiers are especially well-suited to wiring to two subwoofers to wire two subwoofers to a mono amplifier, you need only know how to cut wire, use very simple tools and follow basic instructions cut.
  • Series vs parallel wiring in fact, whenever you plan to connect more than two speakers to a two-channel amplifier – or more than four speakers to a four-channel amp – there are a few things to consider, not the least of which is the amps ability to handle low-impedance loads first, you connect two subwoofers in series and then.

You can hook the subs voice coil in series for 4 ohms per sub then hook the subs up in paralle to the amp or you can hook the subs vc's in parallel for a 1 ohm load per sub then hook them up in series to the amp. How to parallel wire 2 subwoofers onto a mono amp or one channel sergeantpope - komada computer repair how to hook up 2 amplifiers or more (read description) - duration: 12:05. Running 2 subs off it bridged mono will get you the most output btw when you connect 2 subs together and then connect one of them to the amp, electrically this is wiring them in parallel also be sure to cluster the lx18s together either side by side standing or bottoms together laying down.

Hook up two subs mono amp
Rated 5/5 based on 30 review
Chat